2. Barrel Nut Wrench: Used to install free floating handguards of all manufacturers. Closed design spreads torque to the whole nut and prevents breaking.

3. 1/2 X 1/4 Minute Rear Sight Base: Allows 1/2 or 1/4 minute elevation clicks. Oversize fitting pads eliminate sight twist.

4. .052 X .059 Rear Aperture: Uses the M-14NM sight sizes, allows the same zero with either aperture.

5. .040 X .040 Rear Aperture: Undersized to allow redrilling to custom diameters.

6. .50 Front Sight: Provides the same sight picture as M-14NM blade.

7. .55 Front Sight: Provides the same sight picture as M-14 blade.

8. Single Stage Trigger Kit: Crisp 3 - 4 1/5 trigger pull, some fitting required, complete instructions included. Note: Please specify large or small pin (next to order quantity).

1. Aluminum 2: Piece Handguard with Handstop, Hand filling design with adjustable round handstop and bipod stud.

2. Barrel Nut Wrench: Used to install free floating handguards of all manufacturers. Closed design spreads torque to the whole nut and prevents breaking.

3. Rear Sight Base: Allows mounting Redfield Style rear sights on Weaver Scope Rails or Flattop Receivers. Height above bore and eye relief are adjustable. Also available for RPA Sights.

4. Adjustable Front Sight Riser: Allows any combination of front and rear sights to be used. Clamps on .812 muzzle diameter, Undersize bushings and custom over bores available. New Click adjust riser.

5. Gas Manifold: Replaces the front sight base on factory barrels, allows the front sight to be moved to the muzzle on NRA Match Rifles, .750 dia. std, .812 and .875 bores available.

6. Adjustable Buttplate: Replaces the factory buttplate using the original hardware. Adjusts in/out, up/down and cant.

7. Single Stage Trigger Kit: Crisp 3 to 4 1/5 lb trigger pull, some fitting required, complete instructions included.

8. Extended Scope Rail: Weaver Style Rail allows rear sight bases or high magnification scopes to be mounted forward for prone shooting, Gunsmith installation required.

9. AR-10 Handguard with Handstop: Replaces the factory Fiberglass handguard, Supplied with round handstop and bipod stud.

10. Scope Rail Extender: Clamps over factory Flattop Receivers to raise and extend the scope base. Accepts Weaver rings. New Products 2-piece. New Design 2007

2. Aluminum 2-piece Style replaces factory handguards and comes with bipod stud. (Not shown)

3. Compensator: Replaces factory flash hider, reduces recoil and eliminates muzzle rise. Item photo is old, there is a new style in use.

4. Receiver Block: Holds Upper receiver securely for milling carrying handles, installing barrels and drilling/tapping.

1. M-14 Gas Cylinder Wrench: Supports Gas Cylinder when removing/installing plug, includes piston holding fixture for cleaning piston.

2. M-14 Piston Drills: Removes carbon build-up in piston and gas cylinder plug.

3. 10-22 Scope Rail: Attaches to receiver, barrel or both to provide additional rigidity. Accepts all Weaver Style Rings. Drilling and tapping required for barrel installation. Supplied with screws.

4. 1100/870 Trigger Kit: Provides crisp, creep free trigger pull on Remington shotguns. Some fitting required, complete instructions included.

7. M1/M1A Scope Rail: Will fit either M1 Garand or M1A, replaces rear sight and firmly attaches to barrel. Requires drilling and tapping barrel and removal/mod of handguard. M1 rifles will require use of SLED as scope is mounted over receiver. $125

8. Shooting The Wilson Matches Manual: Training manual for shooting the Wilson matches. Includes photographs and complete instructions. For Nat'l Guard shooters.               (Not shown)